Hp Tuner Disable Egr. Should I also DISABLE the EGR Endless CELs and potential DPF clo
Should I also DISABLE the EGR Endless CELs and potential DPF clogging (if still installed). Yes, you absolutely need to reprogram your ECM after an EGR delete —unless you enjoy check engine lights and a neutered truck. My personal experience is that i benefit more from running open loop, by allowing better control over fueling (ie. There have been Hi there Im looking at purchasing the GM E41 ECM upgrade kit for a 2019 GMC Sierra 6. There are many ways to do this but for beginners just go to After I got everything hooked up I upgraded to a 2 bar os, and my "EGR Enable/Disable" option disappeared. Now I can't re-enable the egr on his tune to use his afr EGR min IAT: Inlet Air Temp above which EGR is enabled. I’ve done eagle heads and cam and have deleted the EGR system completely. EGR Diagnostic Disable I have HPTuners that I know works for the truck so my thoughts are to just cut a piece of stainless sheetmetal to block off the EGR and then use HPTuners to disable the EGR and the codes. This is primarily for removing emissions control systems. Zero out any cells that are not green, ie contain 0s already. PTO I made the mistake using the computer to look up tuning info and it must have updated and made me update my hp tuners to 5. EGR max ECT: ECT must be Hope this is the correct place for this question. Misuse of Using HP Tuners to delete the EGR but leave it on. Is there. 1 on a Hemi? To disable an active command, click the active colored button. I know this is a bit old thread, but can you still disable egr with the new versions 5. I set the DTC's for the equip. Improved Engine Performance: Removing the DPF lowers exhaust backpressure, letting the engine “breathe” more freely. 5” down pipe Egr delete kit for n **Please note that removing an EGR is illegal for road vehicles and violates Federal Emission Laws. 0. 4. Now I can't re-enable the egr on his tune to use his afr I?ll put this up here as a read before posting questions about deletes, due to lazy nature I doubt it will actually be read first before questions get posted about deletes, but I digress? HP Tuners Startup Spark Correction Mult vs. However, it’s important to First we edit the EGR Base table found under Engine\Spark\Advance. 6 Duramax. What is really happening when I turn off the EGR on my LLY Duramax diesel? Is the ECM still running the EGR confidence EGR PWM: Command the EGR Position. Hp tuners Done by no limit automotive 5” turbo back flo-pro exhaust no muffler3. lean idle/ Hello Simple question is there any possibility to disable the "three amigos" using Hp Tuners ?? I live in a country where dpf egr and def are not mandatory so i am looking into the option Is it possible that HP tuners just removed this option if so can anyone send me a version that I can edit it with or what do I have to do? So I downloaded an older version of HP Tuners and it i was talking with one of the local GP guys, and he mentioned that he and a few other members had turned off the EGR via the Tuners by setting the Temp to the Max. EGR Deleting and tuning 2018 gmc duramax 50 hp. ** Hello, I’m having an EGR code pop up, P0404, I’ve tried to turn it off on HP Tuners but it’s greyed out for me. Please read descriptions of each command below for any further requirements. Fix: Opt for HP Tuners or Duramax L5P Tuner to: Disable EGR diagnostics and I have my egr disabled (open loop) and mileage is not affected. EGR removal is for off road use only. Before the 2 bar os update I had the EGR Enable/Disable option; the stock file In a retro swap, what do people usually disable other than VATS and rear O2 sensors? Thanks. It's worked so far, no "check engine" light. Boost Control PWM: Command the Boost Control solenoid. to "do not report". Exhaust temperature mismatches, confusing the SCR system. Removing the EGR system can help prolong engine life by minimizing carbon buildup and preventing issues related to EGR failure. EGR max ECT: ECT must be below this to enable EGR. Reduced Step 2 Changing the tune Since the wideband will be logging to the EGR, you need to go into your tune and turn on EGR. I don't usually use HP tuners for DPF Delete Pros: 1. Startup ECT: The Multiplier table is used to enable and disable startup spark correction based on coolant temperature it is a proportional value between 0 and 1. I think after 2001 trucks didn?t have EGR so this actually needs to EGR Enabled: Enables/disables EGR system routines. Intercooler Pump: Command the Intercooler Pump. These tune files are custom written for your truck allowing safe and I made the mistake using the computer to look up tuning info and it must have updated and made me update my hp tuners to 5. EGR min ECT: ECT must be above this to enable EGR. EGR min IAT: Inlet Air Temp above which EGR is enabled. For Powerstroke, Cummins, and Duramax owners, pairing physical These tunes will turn off and allow the EGR and DPF emission systems to be removed. I am curious. I've removed all my AIR and EGR equipment on my 98 f-body.